http://www.hottubworks.com/spa-repair-forum/ HotTubWorks Spa Repair Forum Tag: electrical en Mon, 15 Mar 2010 15:35:02 +0000 http://www.hottubworks.com/spa-repair-forum/topic/troubleshooting-switch-clicks-but-jets-do-not-come-on#post-203 Tue, 11 Aug 2009 13:18:40 +0000 Mary 203@http://www.hottubworks.com/spa-repair-forum/ <p>If you are comfortable using a volt meter then you can turn on the pump and once you have heard the relays click you can take a voltage reading coming off the board going to the pump. If you are not getting any power and the indicator is on the top side then your circuit board is bad. </p> http://www.hottubworks.com/spa-repair-forum/topic/troubleshooting-switch-clicks-but-jets-do-not-come-on#post-200 Thu, 06 Aug 2009 21:09:34 +0000 Anonymous 200@http://www.hottubworks.com/spa-repair-forum/ <p>Thank you for your response. Is there any other test I can do to confirm it before spending the $$$ on a new board? </p> http://www.hottubworks.com/spa-repair-forum/topic/troubleshooting-switch-clicks-but-jets-do-not-come-on#post-195 Thu, 06 Aug 2009 11:24:45 +0000 Mary 195@http://www.hottubworks.com/spa-repair-forum/ <p>It sounds like you are doing all the correct testing. Since you are hearing the relays click when you push the <a href="http://www.hottubworks.com/SpaParts/CabinetSides.php">spa control panel</a> and the fuses have checked good then I think you may have a bad <a href="http://www.hottubworks.com/SpaParts/ElectricalCircuitBoards.php">circuit board</a>. The topside panel is sending the signal to the board, that is the clicking noise you hear. </p> http://www.hottubworks.com/spa-repair-forum/topic/troubleshooting-switch-clicks-but-jets-do-not-come-on#post-193 Wed, 05 Aug 2009 16:05:46 +0000 Anonymous 193@http://www.hottubworks.com/spa-repair-forum/ <p>Have a 3 zone spa with 3 pumps connected to a Balboa M7 (53672-02 2M7P3) controller pack and digital pad. When I push the Jets 3 button (Zone 3) there is an audible click but nothing happens. Zones 1 &#38; 2 work fine, the spa heats and circulates without issue.</p> <p>To test the #3 pump/motor I swapped the Zone 2 &#38; 3 plugs where they connect to the control pack. The #3 pump and motor work fine. When reversed Zone 2 clicks and nothing happens. Put back to normal the result is consistent. The pumps &#38; motors seem to be fine, there are no obvious loose connections, and the 4 fuses inside the controller pack test good with a meter. For some reason power is not getting to the Jets 3 pump.</p> <p>Does the click indicate anything specific? Relay? Control pad, controller pack, circuit board, or something else? What more can I do to chase down the root cause? Thank you! </p> http://www.hottubworks.com/spa-repair-forum/topic/troubleshooting-button-clicks-but-jets-do-not-come-on#post-192 Wed, 05 Aug 2009 15:42:21 +0000 Anonymous 192@http://www.hottubworks.com/spa-repair-forum/ <p>Having a problem with an Infinity Spa. It has 3 pumps for 3 different "zones" connected to a Balboa M7 (53672-02 2M7P3) control pack and digital pad. When I press the "Jets 3" button there is a single audible click but nothing happens. The other 2 zones work fine. The spa heats and circulates without any other issues. </p> <p>I swapped the Jets 2 &#38; 3 plugs that go from the pumps to the control pack to confirm it was/was not a pump/motor problem. When switched Zone 3 (Jets 3 connected to Zone 2) works fine and Zone 2 (Jets 3 button connected to Zone 2) clicks with no result. Swapped back the result is consistent. All pumps and motors seem to be fine and the fuses inside the control pack test good with a continuity meter. </p> <p>How can I further run down the root problem? Does the click indicate anything specific? A relay problem, power, pad/button failure, circuit board, or something else? Thank you! </p>