This Weeks Sale
1-800-770-0292
Mon-Fri - 7am-7pm CT
Sat-Sun - 8am-5pm CT

Hot Tub Jets Not Working?

by

hot tub jets not working

 

Why are my hot tub jets not working?! It’s a common spa question that we get asked all the time. One day you’ll get in the spa and notice the hot tub jets don’t feel as strong as usual.

It’s almost always an easy fix, so don’t worry about major problems right away – it’s probably not the case. There is usually a very simple reason that the jets don’t have much “oomph” lately.

Here’s the step-by-step process that we use in our call center to guide spa and hot tub owners through issues when their spa jets aren’t working.

 

 

Is the Pump Working Right?

hot tub pumpThis is an important first question, but it’s really many questions combined into one. The first part being, “Is the pump air-locked?” This can occur if you just drained the hot tub. Some systems need to “burp” out air in the pipes in front of the pump, which is usually done by loosening the union nut or pump drain plug to allow the air to escape.

Some hot tubs have two pumps – a circulation pump for filtration and a jet booster pump. Many hot tubs just have a single, two-speed pump that accomplishes both functions. So another question would be, “Is the jet pump working?” or “Is the pump’s high speed working?”

If the jets seem to have less than the normal volume of water coming through, be sure that the pump is turning on like normal. Digital spas typically have to push the display to enter the jet mode. Older spa controls use an air button to activate the jet pump. The air switch button and the air hose can fail or lose effectiveness over time, and they may need to be replaced.

 

Dirty Spa Filter?

hot tub filterA dirty spa filter can slow water flow down noticeably, but not completely. Your spa heater won’t work if your water flow rate is very low. So if your heater is working, chances are good that your filter is still pretty clean. A dirty spa filter will also allow small bits of debris to pass through. Replace your spa filters every 12-18 months for best results.

 

Clogged Drain Cover?

hot tub drain coverThe drain covers that are located in the foot well area of a spa or hot tub have very powerful suction, and if something like a napkin, plastic wrap, cup or t-shirt comes close, it can block the water flow. Check that your drain covers are not covered with something that’s blocking the water flow.

 

Low Water Level in Spa?

hot tub water levelIf your spa skimmer is drawing in air, or “sucking air,” this will drastically affect water flow. It will also shut off the spa heater. Is the water level OK in the spa? You may need to add more water every so often to replenish the water lost to evaporation and drag-off. Keeping your spa cover straps clipped helps reduce evaporation by pulling the cover tight against the spa.

 

Air Leak in Front of Pump?

hot tub air leakIn the case of an air leak, it’s usually the pump union in front of the pump that is loose, or it could also be that the o-ring inside is out of position. Then again, it could also be a valve or any pipe connection in front of the pump (the pipe that brings water into the pump). If anything before the pump is loose or cracked, the pump will suck in air. The point that is leaking air when the pump is ON will also leak water when the pump is OFF. With the cabinet door open, shut off the pump and look for any spray or drips on the pipe that goes into the pump.

 

Clogged Pump Impeller?

hot tub pump impellerFor most hot tubs with a good spa cover, the tub stays pretty clean. But if your spa was left uncovered and took on leafy or seedy debris, this debris can clog up the pump impeller. The impeller is a closed vane type, and for many portable spas, there is no pump strainer basket to catch debris.

To check your impeller, shut off power and close the valves on both sides of the pump. Remove pump unions (a gallon or two of water will spill), and turn pump to look inside of the pump impeller housing. If it is clogged, you will usually see some debris in the center eye of the impeller.

To proceed further for cleaning, remove the screws or bolts that hold the impeller housing cover in place. With the impeller exposed, use flexible wire or plastic to ream out the impeller vanes and remove the clogging material. Re-secure the impeller housing cover, tighten the pump unions and open the valves.

 

Is the Jet Adjustable?

hot tub jetMany jets are adjustable at the nozzle or by rotating the outer ring Many can be turned almost off, which increases flow to the other jets nearby. You may find it easier to manipulate the jet adjustment while the pump is off, but it’s not necessary. Try turning the jet nozzle left or right, or turn the jet’s outer ring or “scalloped bezel.”

 

Is the Jet Clogged?

hot tub jetSpa jets can also become clogged, but it doesn’t happen very often. When it does, it’s usually the broken piece of a part that has lodged itself in the jet and is blocking part of the water flow. In some cases, spa jets can become clogged from clumps of calcium or debris that have pushed through the filter. For many spa jets, the internal jet assembly can be removed (unthreaded) from the jet body for inspection. Inground spas with jets that are not easily removable can use a wire or thin rod to ream out the small orifices.

 

Are the Valves All Open?

hot tub slice valveFor most spa and hot tub systems, there are two diverter valves on either side of the pump. These can be closed for equipment service without draining the entire spa. Sometimes these valves will vibrate into a closed position Рespecially slice valves, which are used on many spas. Check that the valves inside the cabinet are open.

Another type of valve is used on some spas to operate different sets or banks of spa jets. Usually a large knob or dial will allow a spa user to open and close jets while seated inside of the spa. Some hot tubs or inground spas may require a valve adjustment outside of the spa. For inground spas, there is often no valve or diverters to adjust individual spa jets, but you can often adjust the jets themselves or turn individual jets on and off.

Air valves will add volume to the water. There are often surface knobs, which can be turned to open or close the air intake line. Open them to see if volume increases sufficiently. Air lines should be closed after use so you don’t bring a continuous stream of cool water into the spa. Doing so will make your heater work harder and cost you more money.

Tags:

Leave a Reply

You must be logged in to post a comment.